All Wheel Trim Ltd.
Unit H, Country Park
Avenue 2, Station Lane
Witney, OX28 4YD
United Kingdom

All Wheel Trim logo click back to start page ! Tel +44 (0)1993 776800
Fax +44 (0)1993 705352

e-mail us:
"with spam protection !"

www.allwheeltrim.co.uk

BACK
HOME
LINKS
ORDER
FIND US

Land Rover 109" and 110" 3/4-Truck cab FITTING INSTRUCTION

OLD-STYLE 3/4-FRAME-PARTS

Galvanized frame parts you'll need to fit a
3/4-old-type-hood
(like the 88"/109") on a standard Truck cab / Pick-up Land Rover.

A - Hood mounting frame
B - Drain channel
C - Roop hook
D - Horse shoe and Staple
LR109 3/4 Click image to see more

FITTING INSTRUCTIONS
Fig. Diagrammatic view of cab and rear body, showing position of hood mounting frame, drain channels, rope hooks and staples. 88" 3/4 - 109" 3/4 model illustrated.

TO FIT:
1. Position the drain channels against the rear panel so that the lower edge rests on the rear body front capping; each drain channel should protrude approximately 1/8in. (3mm) out from the body side capping. The drain channels are shaped to go round the hoodstick.
2. Using the drain channels as templates, drill six holes 17/64in. (7mm) diameter and secure the channels to the cab rear panel, using the fixings provided.
3. Position the hood mounting frame centrally against the cab rear panel and resting on the drain channels.
4. Using the mounting frame as a template, drill six holes 17/64in. (7mm) diameter and secure the channels to the cab rear panel, using the fixings provided.
5. Fit the rear hood sticks in the sockets at the rear corner of the body and secure with clamp arms, bolts, washers and nuts.
6. Fit the front hood sticks in the sockets at the rear corner of the body and secure with clamp arms, bolts, washers and nuts.
7. Secure the tie tubes between the sticks, using self-locking nuts.
8. Fit the intermediate hood stick between the tie tubes, securing it with self-locking nuts.
9. 109" models: secure the hood stick flanges to the pre-drilled holes in the body side capping, using the fixings provided.
10. Mark centre 9in. (230mm) from the door post and 2in. (50mm) down from the top of the rear body capping and, using the frond rope hooks as templates, drill four holes and fix the rope hooks to the body sides, using the 2 B.A. nuts bolts and washers provided.
NOTE: Two rope hooks are handed, 1xLH, 1xRH, the hooks should be towards the door.
11. Secure the two staples to the rear body, adjacent to the top of the tailboard, using the existing holes and fixing with the 3/4in. (19mm) long 2 B.A. screws, nuts and washers.
Early Series II models:
12. Place the hood over the hoop sticks and secure to the mounting frame on the cab. The hood retaining strip should be inserted in the top and side channels of the hood. Peg the upper retaining strip into the side strip.
13. Fit the lower ends of the two side retaining strips to the staples on the mounting frame and secure with the short straps.
Late Series II and all Series IIA and III models:
14. Place the hood over the hood sticks and secure to the mounting frame on the cab. The hood retaining strips should be inserted in the top and side channels of the hood. Peg the side retaining strips into the top retaining strip.
15. pull the hood down tight around mounting frame, and mark off position and drill cab panel for fitting strap retaining stud. Secure hood.
16. Fasten the two straps over the intermediate hood stick, secure the ropes to the rope bracket on the body sides and, together with the rear ropes, to the hooks at the rear of the body.
17. Secure the rear curtain straps to the two staples fitted to the rear of the body.
18. Push the rear curtain side flaps through the side pockets and secure.

109" 3/4-frame with all the parts to fit a hoot
OLD-TYPE CAB-fixing
fit's a 109" Truck cab Land Rover / Pick-up and 110" 3/4-old type
109" 3/4 frame

Land Rover 110" 3/4 110" 3/4-frame with all the parts to fit a hoot
NEW-TYPE BULKHEAD fixing
fit's a 110" Truck cab Land Rover / Pick-up 3/4-new type